Estun All models error codes
Codes
- A200VError codeVoltage A 200VAC
- Fn000Error codeDisplay alarm history
- Fn003Error codeAutomatic offset-signal adjustment of motor current detection
- L1Error codePlease properly handle PA0 cable connector /PA0 PB0 PG frequency divi /PB0 output PC0 /PC0 SG /V-CMP+ Spee （/COIN+) （Wh O /V-CMP- Positi （/COIN-) （Wh co /TGON+ TGON /TGON- （When sett /S-RDY+ Servo /S-RDY- （Whe /CLT+ Torqu /CLT- （Whe * setti /BR+ Brake /BR- （Whe rele /PGCO+ /PGCO- Encod OT+ OT- Overtr /RD+ Servo /RD- excitat ALM+ +24V 1Ry 0 V Alarm outpu （When Ala ALM- Photocouple Max.applica Max.applica
- L1CError codeGround terminals
- L2CError codeServo Motor connection terminals
- Pn003Error codeSelect operations to be made upon power interruption [0] gives no output of servo alarm signal（ALM） [1] Output servo alarm signal （ALM）
- Pn004Error code[0] When servo is OFF or alarm occurs, DB is enabled [1] When servo is OFF or alarm occurs, motor coasts to a stop [2] When servo is OFF or alarm occurs, DB is enabled and will not release until motor stops [3] When servo is OFF or alarm occurs, motor coasts to a stop, then DB is enabled
- Pn005Error codeClear error pulse signal is turn ON or not after Servo OFF [0] Turned on [1] turned off
- Pn008Error codeReference pulse form
- Pn010Error codeuses analog current limit function or not [0] Does not use analog current limit function [1] Uses analog current limit function
- Pn016Error codeSpeed error
- Pn028Error codeForward external current limit
- Pn029Error codeSpeed coincidence error
- Pn030Error codeIn position error
- Pn031Error codeoverflow range of error counter
- Pn036Error codeError counter overflow
- Pn042Error codeServo motor model selection [0] set as 0 for EDC-02、04、08 [1] special model servo motor
- Pn045Error codeSpeed Level at which Brake Signal Is Output during Motor Operation
- Pn046Error codeOutput Timing of Brake Signal during Motor Operation
- Pn047Error codeEnable/Disable alarm when position error pulse overflows [0] no alarm output [1] output alarm
- Pn052Error code0: incremental 1: absolute
- Pn091Error codeEncoder wrong alarm on
- Pn095Error codeIncrease overload capacity
- Pn097Error codeAlarm inspection smoothing time constant
- Pn120Error codeCurrent feed forward compensation
- Pn203Error codeMotor reverse turnaround time [electric knife frame function]
- Pn204Error codeMotor reverse angle [electric knife frame function]
- Pn210Error codeCommunication address setting
- Pn211Error codeCommunication speed options: 0：4800bps 1：9600 bps 2：19200bps
- Pn212Error codeCommunication protocol form: 0：7，N，2（Modbus,ASCII） 1：7，E，1（Modbus,ASCII） 2：7，O，1（Modbus,ASCII） 3：8，N，2（Modbus,ASCII） 4：8，E，1（Modbus,ASCII） 5：8，O，1（Modbus,ASCII） 6：8，N，2（Modbus,RTU） 7：8，E，1（Modbus,RTU） 8：8，O，1（Modbus,RTU）
- Pn213Error codeCommunication protocol options: 0：Self-definition protocol RS-232 Communication 1：MODBUS Protocol RS-422/232 Communication 2：MODBUS Protocol RS-485 Communication
- Pn216Error codeCommunication bit control: This parameter is designated through bit to decide input source of digital input port. Bit0~bit7 represent input port 0~7 respectively. Bit definition represents as follows: 0 : input bit is controlled by outside interface 1：input bit is controlled by communication
- Pn218Error codeSuitable motor type parameter
- Un003Error codeUn009
- Un008Error codeCurrent motor position is 5 digits lower (×1 pulse)
- Un009Error codeCurrent motor position is 5 digits higher (×10000 pulse)