Epson All models error codes
Codes
- *Error codeMotor Driver uses different parts depending on manipulator models. Refer to the next page for Motor Driver selection
- 0000Error codeCR PID sürüş süresi
- 0xError code0xE1
- 1Error codeAC Servo Motor (50 W)
- 2Error codeSuitable cord (Length about 800 mm)
- 3Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locations
- 4Error code■ Do not remove the connector plate forcibly. Removing the connector plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector plate. Be sure to place the cables back to their original locations
- 5Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locations
- 7Error codeFour digits
- 30Error codeThis is usually caused by a program input error
- 33Error codeThis error occurs when large amounts of data are being transmitted
- 34Error codeThis error occurs when the transmission is affected by line noise or other interference. Determine the cause of the interference (such as an extra-long cable or a crimped cable, or a nearby noise-generating device) then retry the transmission
- 0300Error codePE detector error
- 0310Error codeHead Hot - baskı öncesi
- 0330Error codeDiğer mürekkep aygıtı hatası
- 0340Error codeHome position error
- 400WError codeMaintenance parts
- 0479Error code"Sistem Hatası" (genel kapsamlı)
- 627Error codeSuitable cord (Length about 800 mm)
- 750Error codeMaintenance parts
- 1000Error codeADF PID aşırı hız
- 1042Error codeKoruma kapağı (safeguard) açıkken çalıştırılamaz
- 1043Error codeHata durumu varken çalıştırılamaz
- 1048Error codeDüşük gerilim algılandıktan sonra çalıştırılamaz
- 1123Error codeDosya hatası. I/O etiket dosyası bozuk
- 1126Error codeDosya hatası. Yazılım opsiyon bilgisi bozuk
- 1150Error codeDosya hatası. Hata geçmişi geçersiz
- 1200Error codeDerleme hatası, derleme mesajını kontrol edin
- 1201Error codeBağlama (link) hatası, link mesajını kontrol edin
- 1514Error codeMaintenance parts
- 2030Error codePanel Unit arızası
- 2051Error codeCard Board arızası
- 2229Error codeDC (PROPELLER TYPE) FAN
- A3Error codeFailure in firmware updating
- A3957SError codeIC4,5
- A6627SError codeIC6
- A6628SError codeIC7/IC13
- age142Error codeCR motor assembly (517) (Page 168)
- age165Error codeConnection failure between the auto cutter unit and the main circuit board unit
- B0HError codeApplication error
- B8Error codeAbnormal Response
- C3500Error codePower supply
- CN1Error codeCN1 or CN2 on the CCD sensor board is disconnected
- CN3Error codeTo the CR Motor
- CN15Error codeCR motor assembly (517)
- CN16Error codePressure pump motor
- CN17Error codePF motor IS pump unit motor
- CN20Error codeCutter motor
- CN21Error codeSuction fan (507)
- CN29Error codePressure pump unit (551)