Epson robot All models error codes
Codes
- *Error codeMotor Driver uses different parts depending on manipulator models. Refer to the next page for Motor Driver selection
- 0000Error codeCR PID sürüş süresi
- 1Error codeAC Servo Motor (50 W)
- 2Error codeSuitable cord (Length about 800 mm)
- 3Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locations
- 4Error code■ Do not remove the connector plate forcibly. Removing the connector plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector plate. Be sure to place the cables back to their original locations
- 5Error code■ Do not remove the connector sub plate forcibly. Removing the connector sub plate forcibly may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. ■ When installing the connector sub plate, be careful not to allow the cables to interfere with the plate mounting and do not bend these cables forcibly to push them into the cover. Unnecessary strain on cables may result in damage to the cables, disconnection, and/or contact failure. Damaged cables, disconnection, or contact failure is extremely hazardous and may result in electric shock and/or improper function of the robot system. When routing the cables, observe the cable locations after removing the connector sub plate. Be sure to place the cables back to their original locations
- 7Error codeFour digits
- 30Error codeThis is usually caused by a program input error
- 33Error codeThis error occurs when large amounts of data are being transmitted
- 34Error codeThis error occurs when the transmission is affected by line noise or other interference. Determine the cause of the interference (such as an extra-long cable or a crimped cable, or a nearby noise-generating device) then retry the transmission
- 0300Error codePE detector error
- 0310Error codeHead Hot - baskı öncesi
- 0330Error codeDiğer mürekkep aygıtı hatası
- 0340Error codeHome position error
- 400WError codeMaintenance parts
- 627Error codeSuitable cord (Length about 800 mm)
- 750Error codeMaintenance parts
- 1000Error codeADF PID aşırı hız
- 1514Error codeMaintenance parts
- 2030Error codePanel Unit arızası
- 2051Error codeCard Board arızası
- 2229Error codeDC (PROPELLER TYPE) FAN
- M3Error codeSuitable cord (Length about 800 mm)
- M4Error codeSuitable cord (Length about 800 mm)
- mm1Error codeForce gauge
- ror30Error codeThis is usually caused by a program input error
- ror33Error codeThis error occurs when large amounts of data are being transmitted
- ror34Error codeThis error occurs when the transmission is affected by line noise or other interference. Determine the cause of the interference (such as an extra-long cable or a crimped cable, or a nearby noise-generating device) then retry the transmission