Delta Electronics sürücü All models error codes
Codes
- A-09Error codeTreatment of the Erroneous Feedback Signals
- a00Error codeContent of Multi- function Display
- a0-03Error codeStart-up Display Selection
- a0-04Error codeContent of Multi-Function Display
- a02Error codeSource of First Master Frequency Command
- a03Error code0: Analog frequency meter 1: Analog current meter
- a07Error codeTorque Compensation (Motor 0)
- a7-00Error codeMotor Rated Current
- a7-01Error codeMotor No-Load Current
- a08Error codeCompensation Coefficient for Motor Instability
- a9-00Error codeCommunication Address
- a9-02Error codeTransmission Fault Treatment
- a9-04Error codeCommunication Protocol
- a10Error codeOffset Level of Liquid Leakage
- a13Error codeDetection Time for Feedback Signal Fault
- B1Error codeMain power terminals Do not connect 3-phase model to one-phase power. It is unnecessary to consider phase-sequence for these terminals R/L1, S/L2 and T/L3. Both ends of the MC should have an R-C surge absorber. Please make sure to fasten the screw of the main circuit terminals to prevent sparks which is made by the loose screws due to vibration. Please use voltage and current within the specification. When using a general GFCI (Ground Fault Circuit Interrupter), select a current sensor with sensitivity of 200mA or above and not less than 0.1-second operation time to avoid nuisance tripping. Please use the shield wire or tube for the power wiring and ground the two ends of the shield wire or tube.
- Bit10Error code1: Operation command controlled by communication interface
- CE01Error codeModbus function code error
- CE02Error codeModbus data address error
- CE03Error codeModbus data value error
- CE04Error codeModbus slave drive error
- CE10Error codeModbus transmission time-Out
- cm2Error codeSurrounding Temperature
- d4Error codeExternal Fault (Normally Open)
- d5Error codeExternal Fault (Normally Closed)
- d6Error codehe output will be activated when low voltage is detected
- d8Error codehe output will be activated when faults occur (oc, ov, H, oL, oL1, EF, cF3, HPF, ocA, ocd, ocn, GF)
- d16Error codeAC Motor Drive Ready
- D1021Error codeOutput current
- ED23Error codeRated Output Current（A）
- ED43SError codeRated Output Current（A）
- is500kError codeWhen the mains power capacity is too large, line impedance will be small and the charge current will be too high. This may damage AC motor drive due to higher rectifier temperature
- J3Error codeEncoder voltage input. Use SW2 to set +5V/+8V
- JP1Error codeGround Terminal Connect the power supply of the motor drive to the ground. Support PG shielding
- JP3Error codeGround Terminal Connect the power supply of the motor drive to the ground. Support PG shielding
- M1005Error codeFault indication of the AC motor drives
- M1007Error codeThe operation direction of AC motor drives (FWD: 0, REV: 1)
- M1016Error codeParameter read/write error
- M1025Error codeRUN(ON) / STOP(OFF) the AC motor drive
- MI1Error codeMulti-function input 1~8
- MI3Error codeMulti-function Input 3
- MI5Error codeMulti-function Input 5
- MI8Error codeDigital frequency meter DFM DCM
- MO1Error codeMulti-function output terminal 1 (photocoupler)
- Pr02Error code11~Pr02-16: MO#46: Malfunction Indication
- RA1Error codeMulti-function relay output 1 (N.O.) a
- SW2Error codeSwitching USB port
- T1Error codeC drive output terminals for connecting 3-phase induction motor
- TB1Error codePower output of encoder Note: Use SW1 to set up output voltage Voltage: +5V±0.5V or +12V±1V Current: 200mA max
- TB2ParameterOutput signal of the push-pull frequency divider Factory setting: Output amplitude is about +24V. Use SW2 to cut off the internal default power. Input required power (i.e. output voltage’s amplitude) DVI voltage range Max: 24V (Push-Pull Voltage Output) Max. output frequency: 100kHz Support frequency dividing output, the frequency dividing range: 1~31Hz