Case All models error codes
Codes
- dAL87Error codeAn invalid date or time has been detected. This situation may be corrected by changing the Real Time Clock (RTC) to a valid value using DataLINE
- dAL88Error codeA write of critical DataCORDER information to the EEPROM has failed
- dAL89Error codeAn error has been detected in the process of writing daily data to the non- volatile FLASH memory
- dAL90Error codeThis alarm is for future expansion, and is not in use at this time
- dAL91Error codeThe DataCORDER alarm queue is determined to be full (eight alarms)
- dC6-13Error codeCurrent values of the network data points (as configured). Data point 1 (Code 6) is generally the humidity sensor and its value is obtained from the Control- ler once every minute
- dC15-19Error codeThese codes are for future expansion, and are not in use at this time
- dC20-24Error codeCurrent calibration offset values for each of the five probes: supply, return, USDA #1, #2, and #3. These values are entered via the interrogation pro- gram
- dC25Error codeThis code is for future expansion, and is not in use at this time
- dC26Error codeThe DataCORDER serial number consists of eight characters. Function code dC26 contains the first four characters. Function code dC27 contains the last four characters. (This serial number is the same as the Controller serial num- ber)
- dC28Error codeAn approximation of the number of logging days remaining until the Data- CORDER starts to overwrite the existing data
- dC29Error codeNumber of days of data that are currently stored in the DataCORDER
- dC30Error codeThe date when a Trip Start was initiated by the user.
- dC31Error codeİsteğe bağlı pil takımının mevcut durumunu gösterir. PASS: Pil paketi tamamen şarj oldu. HATA: Pil takımı voltajı düşük
- dC32Error codeCurrent time on the real time clock (RTC) in the DataCORDER
- dC33Error codeCurrent date (month and day) on the RTC in the DataCORDER
- E01Error codeIndoor-remote controller communication trouble (detected at remote controller end)
- E2Error codeIndoor unit refrigerant leak detection sensor output*
- E03Error codeCommunication from remote controller or network adaptor has been lost (so has central control communication)
- E04Error codeTrouble or poor contact in wiring between indoor and outdoor units (loss of indoor-outdoor communication)
- E06Error codeTrouble reception in indoor-outdoor communication (dropping out of indoor unit)
- E07Error codeSignal cannot be transmitted to indoor units ( indoor units left without communication from outdoor unit)
- E09Error codeBoth remote controls have been set as master remote control in two remote control (alarm and shutdown for header unit and continued operation for follower unit)
- E10Error codeCommunication trouble between main MCU and the motor microcomputer MCU
- E11Error codeCommunication check code between Application control kit and indoor unit P.C. board
- E16Error codeToo many indoor units connected / overloading
- E17Error codeThere is no communication from FS unit(s)
- E18Error codePeriodic communication between indoor header and follower units cannot be maintained
- E20Error codeDetection of refrigerant piping communication trouble during automatic address setting
- E23Error codeTrouble transmission in outdoor-outdoor communication
- E26Error codeTrouble reception in outdoor-outdoor communication, dropping out of outdoor unit
- E31Error codeThere is no communication between P.C. boards in inverter box
- F01Error codeHeat exchanger temperature sensor (TCJ) has been open / short-circuit
- F02Error codeHeat exchanger temperature sensor (TC2) has been open / short-circuit
- F03Error codeHeat exchanger temperature sensor (TC1) has been open / short-circuit
- F04Error codeOutdoor discharge temperature sensor (TD1) has been open/short-circuited
- F05Error codeOutdoor discharge temperature sensor (TD2) has been open/short-circuited
- F06Error codeOutdoor heat exchanger liquid side temperature sensors (TE1, TE2, TE3) have been open/ short-circuited
- F07Error codeOutdoor liquid temperature sensor (TL1,TL2,TL3) has been open/short-circuited
- F08Error codeOutdoor air temperature sensor (TO) has been open/short-circuited
- F09Error codeOutdoor heat exchanger gas side temperature sensors (TG1, TG2, TG3) have been open/ short-circuited
- F10Error codeAmbient temperature sensor (TA) has been open / short-circuit
- F11Error codeDischarge temperature sensor (TF) has been open / short-circuit
- F12Error codeOutdoor suction temperature sensor (TS1,TS3) has been open/short-circuited
- F13Error codeTemperature sensor built into indoor IPM (TH) has been open/short-circuited
- F15Error codeWiring trouble in outdoor temperature sensors (TE1,TL1) has been detected
- F16Error codeWiring trouble in outdoor pressure sensors (Pd, Ps) has been detected
- F22Error codeOutdoor discharge temperature sensor (TD3) trouble Low pressure sensor (Ps) trouble High pressure sensor (Pd) trouble Outdoor unit pressure sensor trouble Occupancy sensor trouble Indoor unit EEPROM trouble
- F23Error codeOutput voltage of low pressure sensor (Ps) is zero
- F24Error codeOutput voltage of high pressure sensor (Pd) is zero or provides abnormal readings when compressors have been turned off