Belarus traktör All models error codes
Codes
- A1Error codeElectromagnet of hydraulic valve group
- A4Error codeAir output temperature control
- BK1Error codeTemperature indicator sensor
- BN1Error codeFuel level indicator sensor
- BP1Error codeEngine oil pressure gauge
- BP2Error codeAir pressure sensor
- BV1Error codeRotational speed sensor
- BV2Error codePTO speed sensor
- by10Error codeWrong choice of hydraulic motor for the implement. Hydraulic motor oil consumption should be by 10…15% below pump output flow at engine operating speed
- by20Error codeWhen releasing the steering wheel in both end-point positions, there is no turn-through of the steering wheel (by 20…30mm) in the opposite direction due to the action of dosing pump springs (the spool does not return to the neutral, the pressure in charge hydraulic line does not drop) due to the following reason: - excessive friction or blocking up of steering drive mechanical compo- nents
- by25Error codeWhen performing the transport works on hard surface roads, increase the pressure
- DL1Error codeLow pressure of oil delivered to the actuating mechanism of DL 1)
- DL2Error codeLow pressure of oil delivered to the actuating mechanism of DL 2)
- dle1Error codebox valve control 1 shall be lowered until its full fixing
- EHS1Error codeDistribution valve EHS-PWM R917 000b 145
- F1Error code
- F19Error codePower supply to NOx sensors of SCR system
- FU7Error codePower supply to conditioner electric motor
- FU27Error codeTest instruments, sensors of speed, RPTO and fuel volume
- ges1Error codenals from the neutral sensor of the range reduction unit and from the sensor of
- H-1Error codeReplace pump
- HG1Error codepilot lamp-alarm of the overvoltage in the on-board power supply system (red)
- HG2Error codepilot lamp-alarm of the parking brake application (red)
- HL4Error codeAlarm lamp of emergency pressure drop in engine
- low0Error codeOil pressure in pilot hydraulic sys- tem is below 0.8 MPa
- M6Error codeFan motor
- M7Error codeFan motor (120 W)
- min-1Error code
- mum300Error codeearly morning, do not switch the fan on
- of44Error code4. Do not overload the engine, do not
- P3Error codeEngine oil pressure indicator
- P5Error codeVoltage indicator
- P6Error codeEngine coolant temperature indicator
- R-23LError codeDeadlock of the lowering valve of a regulatory section ȿɇR -23LS (if integrated unit BOSCH is installed)
- R1Error codeAddional resistor of the fan motor
- rom1Error codeOne of the drives (RA DL, FDA, FPTO, RPTO) or a gear can be engaged only for a very short period (from 1 to 6 sec), or becomes disengaged after engagement
- rom14Error codeOperation is performed only by maintenance department Contact the dealer. Pump does not generate pump due to low efficiency coefficient
- RUS-1822Error codeLoss of sealing of work spaces of main and operating cylinders due to damage, wear and tear of cups and O-rings (on tractors “BELA- RUS-1822ȼ.3/2022ȼ.3” damage of valves is possible)
- RUS-3522Error code- reverse motion steering column with a dosing pump
- S1Error codeFan modes switch
- SA4Error codeFan switch
- SBError codePosition sensor 0 538 009 140
- SB1Error codeFault signalling switch
- SB2Error codeFault signaling switch
- SK1Error codeEmergency temperature sensor
- SP1Error codeAir cleaner clogging sensor
- SP2Error codeEmergency air pressure sensor
- SP3Error codeEmergency oil pressure sensor
- to6Error codePressure sensor, installed at a control valve output of a drive or a gear, does not respond. The failure is displayed by three-times flash of the corre- sponding power-on indicator
- UZ1Error codeVoltage converter