Belarus traktör All models error codes
Codes
- 0Error codeFaulty location of pressure control valve adjusting cap
- 0-16Error codeNo AB charging (low charging voltage
- 1Error codeswitch 2 allows to change temperature of cold and dry air outcoming from deflectors 6 (fig
- 2Error codeHigh pres- sure fuel pump
- 2-15Error codealternator driving belt and voltage
- 2bError codeFailure, external manifestation, cause
- 3Error codeInternal tire pressure of rear wheels set as pres- sure for 30km/h speed
- 4Error codeWith the help of the switch 1 you can change air flow by changing fan speed. The
- 5Error code5 Hydraulic system working pressure, MPa
- 5MError codeSpontaneous lowering of RLL (lowering without a command received from the instrument panel or remote control buttons)
- 6Error code6 Pressure relief cracking pressure, MPa
- 7Error codeEngine oil temperature
- 8Error codeFaulty pressure sensor “ȾɋȾɆɆ” of GB reducing unit first or top gear accordingly, or burned-out lamp indicating GB reducing unit en- gagement, or burned-out GB re- ducing unit led lamp
- 9Error code9 Coupling thread of fast-coupling joint sleeves, mm: - oil pressure pipeline and oil drain pipeline Ɇ20u1,5 - free-drain oil pipeline Ɇ24u1,5 ________________________________________________________________________________________________________________________________ 1) At rated engine rpm
- 11Error codeFailure, external manifestations, cause
- 12Error codeFailure, external manifestations, cause
- 13Error codesolenoids or short circuit
- 14Error codeFailure in remote control
- 15Error codemode (when the outside temperature is above +15°C) for 15…20 min once in fifteen days
- 16Error codeShort circuit may occur in
- 16bError codeFailure, external manifestations, cause
- 21Error codeLow power supply voltage (less than 11 V). Meanwhile the central spool of the distribution valve sec- tion spontaneously goes back to the “neutral” position. Control by the joystick or by the HLL POU can not be executed. If the voltage is below 11 V and if an actuating signal is available, the code “17” will be initi- ated instead of code “21” until the control is stopped
- 22Error codetric circuit diagram of the RLL control system (figure
- 23Error codeFailure of the control
- 24Error codeFailure of the control
- 25Error codeClean filter cartridges of ventilation and air heat-
- 26Error codepump drive belt
- 28Error codeTo check if it is failure of the sensor or the cable (in
- 31Error codecable to the sensors (left and right) and interchange
- 32Error codewas replaced by 31), that means that the sensor is
- 34Error codeFailure of the control
- 36Error codeeliminate the failure in the RLL hydraulic system
- 37Error codeClean filter cartridge of air pressure regulating filter
- 41Error codeHigh power supply voltage (more than 45 V). Meanwhile the central spool of the distribution valve sec- tion spontaneously goes back to the “neutral” position. Control by the joystick or by the HLL POU can not be executed. The error code is indi- cated in all sections regardless of presence (absence) of the actuating signal
- 42Error codeIntensity of current in the control valve is beyond the permissible or desirable range. Meanwhile the cen- tral spool of the section is perma- nently in the “neutral” position. Con- trol by the joystick or by the HLL POU can not be executed. The error code is indicated in the damaged sections when there is an actuating signal
- 43Error codeFailure of the inductive position sensor of the central spool. The er- ror code is indicated in the damaged sections only immediately after volt- age supply
- 44Error codeClean filter cartridge of air pressure regulating
- 47-63Error codeend switch on the casing of the motor with
- 55Error codevalves and rocking arms
- 61Error codeReplace filter cartridge in the cabine ventilation
- 65Error codeTilting, deadlock of spool of adjust-
- 70Error codePressure control valve gets actuated frequently (engages pneumatic com- pressor) without air bleeding from receiver tank
- 70-152Error codeDeadlock of the lowering valve of a regulatory section (if hydraulic unit Ɋɉ70-1523.1 is installed)
- 72Error codeChange filter cartridges of ventilation system
- 77Error codeDirt accumulation in cavities and channels of pressure control valve
- 79Error codeAdjust valves of GB centrifuge
- 80Error codeDamaged rubber parts of pressure
- 81Error codeThe central spool of the distribu- tion valve section does not shift back in “neutral” position. Control by the joystick or by the HLL POU can not be executed. The central spool is blocked in “lift” “lowering” or “float- ing” position. If the abovementioned failures occur the error code “24” is indi- cated once, and then code “81” is indicated permanently
- 82Error codeBefore the controls are engaged, the central spool of the section is in the “lift” position. Control by the joy- stick or by the HLL POU can not be executed. The error code is indi- cated in the damaged sections only immediately after voltage supply. The error code is indicated only if the central spool of the section is in the “lift” position before the controls are engaged. If the spool is in ”low- ering” position, code “43” is indi- cated
- 83Error codeSoftware error. In this case con- trol by the joystick or by the HLL POU can not be executed