Bambu Lab All models error codes
Codes
- 0CError codeBuild plate localization marker was not found
- 07FError codeAMS assist motor is overloaded. Please check if the spool or filament is stuck. After troubleshooting, click the "Retry" button
- 12FError codeFailed to get AMS mapping table; please click the "Retry" button to continue
- 0300-400Error codeThe AMS failed to change filament
- 0300-800Error codeA Filament pile-up was detected by the AI Print Monitoring. Please clean the filament from the waste chute
- 0300-801Error codeThe filament has run out, please load new filament in the "filament" page
- 0500Error codeMicroSD Card read/write exception. please reinsert or replace MicroSD Card
- 0500-400Error codePrint jobs are not allowed to be sent while updating firmware
- 0500-401Error codeThe MicroSD Card is write-protected. Please replace the MicroSD Card
- 0500-402Error codeThe Micro SD card sector data is damaged. Please use the SD card repair tool to repair or format it. If it still cannot be identified, please replace the Micro SD card
- 0500-403Error codeThe nozzle diameter in sliced file is not consistent with the current nozzle setting. This file can't be printed
- 0500-801Error codeThe print file is not available. Please check to see if the storage media has been removed
- 0500-803Error codeYour sliced file is not consistent with the current printer model. Continue?
- 0501-401Error codeAuthorization timed out. Please make sure that your phone or PC has access to the internet, and ensure that the Bambu Studio/Bambu Handy APP is running in the foreground during the binding operation
- 0501-402Error codeCloud access failed, which may be caused by network instability due to interference. You can try moving the printer closer to the router before you try again
- 0501-403Error codeQR code binding is in progress, so device discovery binding cannot be performed. You can scan the QR code on the screen for binding or exit the QR code display page on screen and try device discovery binding
- 0514-403Error codeDevice login has expired, please try to bind again
- 0700-400Error codeThe AMS has been disabled for a print, but it still has filament loaded. Please unload the AMS filament , and switch to the spool holder filament for printing
- 0700-800Error codeThe cutter is stuck. Please make sure the cutter handle is out
- 0700-801Error codeThe AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool
- 0701-400Error codeFilament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing
- 0701-800Error codeFailed to extrude the filament. Please check if the extruder clogged. After troubleshooting, click the "Retry" button
- 0701-801Error codeThe AMS assist motor is overloaded. This could be due to entangled filament or a stuck spool
- 0702-400Error codeFilament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing
- 0702-800Error codeFailed to pull back the filament from the toolhead to AMS. Please check whether the filament or the spool is stuck. After troubleshooting, click the "Retry" button
- 0702-801Error codeAMS assist motor is overloaded. Please check if the spool or filament is stuck. After troubleshooting, click the "Retry" button
- 0703-400Error codeFilament is still loaded from the AMS after it has been disabled. Please unload the filament, load from the spool holder, and restart printing
- 0703-800Error codeFailed to pull back the filament from the toolhead to AMS. Please check whether the filament or the spool is stuck. After troubleshooting, click the "Retry" button
- 0703-801Error codeAMS assist motor is overloaded. Please check if the spool or filament is stuck. After troubleshooting, click the "Retry" button
- 1000Error codeEnabling traditional timelapse might lead to defects. Please enable it as needed?
- 1001Error codeTimelapse is not supported because Spiral vase is enabled in slicing presets
- 1200-400Error codeFilament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job
- 1200-800Error codeCutting the filament failed. Please check to see if the cutter is stuck. Refer to the Assistant for solutions
- 1200-801Error codeAMS filament ran out. Please insert a new filament into the same AMS slot
- 1201-400Error codeFilament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job
- 1201-800Error codeFailed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the "Retry" button
- 1201-801Error codeFailed to get AMS mapping table; please click the "Retry" button to continue
- 1202-400Error codeFilament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job
- 1202-800Error codeFailed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the "Retry" button
- 1202-801Error codeFailed to get AMS mapping table; please click the "Retry" button to continue
- 1203-400Error codeFilament is still loaded from the AMS when it has been disabled. Please unload AMS filament, load from spool holder, and restart print job
- 1203-800Error codeFailed to pull back the filament from the toolhead. Please check whether the filament is stuck. After troubleshooting, click the "Retry" button
- 1203-801Error codeFailed to get AMS mapping table; please click the "Retry" button to continue