ABB All models error codes
Codes
- E.6Error codeCPU Fault in the Mitsubishi FR-E700 Drive indicat
- E018Error codeGround Fault
- E019Error codelleak sense.fail
- E19Error codePosition Error (Following Error) in the Allen-Bra
- E020Error codeSelf Test Error 1
- E021Error codeSelf Test Error 2
- E022Error codeSelf Test Error 4
- E023Error codeDC in error
- E024Error codeInternal error
- E026Error codeVref Error
- E027Error codeError Meas V
- E028Error codeError Meas F
- E029Error codeMid Bulk OV
- E030Error codeError Meas leak
- E031Error codeThe
- E032Error codeError Read I
- E035Error codeRemote Off
- E036Error codeVout Avg error
- E046Error codeString self-test fails
- E049Error codeAC FF Error
- E056Error codeOver-Temp. (from the external box)
- E057Error codeVbulk reading error
- EN6020Error codeAşağıdakilere dayanarak: • Bakır kablolar için NEC Tablo 310-16 • 90 °C (194 °F) kablo yalıtımı • 40 °C (104 °F) ortam sıcaklığı • oluk ya da kablo içerisindeki ya da topraklı (doğrudan gömülü) akım taşıyıcı iletkenler üçten fazla değildir • eşmerkezli bakır muhafazalı kablolar
- EN6052Error codeMuhafazalar tarafından sağlanan koruma derecesi (IP kodu)
- EN6100Error codeGenel düşük gerilim sistemlerine bağlı ekipmanlar tarafından üretilen harmonik akımları sınırlayan EMC standardı
- Er10Error codeDynamic output short circuited to foreign voltage
- Er12Error code_ Short circuit between two dynamic inputs
- Er13Error codeStatic output Q10..17 (Q20..27) short circuited to 0V or safety Q2, Q3 overloaded
- Er14Error codeStatic output Q10..17 (Q20..27) short circuited to 24V
- Er18Error codeCAN-bus fault. (Short circuit, termination resistor, etc.)
- Er21Error codePLC-program CRC-error
- Er24Error codeErroneous PLC-code. Invalid PLC-instructions
- Er26Error codeBaud rate conflict. Unit programmed for other baud rate than current bus baud rate. Note that Pluto must be rebooted after change of baudrate in the PLC program
- Er40Error codeError safety output Q2 or Q3. Q2, Q3 connected together or to other negative voltage. Q2, Q3 has too high capacitive load
- Er41Error codeError output Q2 or Q3. Overload or connected to foreign positive voltage
- Er42Error codeError relay output. No answer from internal relay monitoring when output is off
- Er43Error codeError relay output. (Self test of transistors)
- Er44Error codeError relay output. Internal relay does not switch on
- Er46Error codeAnalogue input error. **(See below)
- Er47Error codePositive voltage on Q2 and/or Q3
- Er50Error codeInput data difference between processor A and B. Processor A and B reads an input differently. The fault is often caused by a bad sensor
- Er58Error codeAS-i safety code table CRC error
- Er59Error codeCalibration analogue functions CRC fault
- Er60Error codeSystem error Twin self test monitoring
- Er61Error codeSystem error Timer IRQ monitoring
- Er62Error codeSystem error Internal serial communication
- Er66Error code5 volt under/over voltage monitoring **(See below)
- Er67Error codeCPU-test error
- Er68Error codeRam-test error
- Er72Error codeSystem error. No communication AUX processor